Tuesday 29 August 2017

Went sailing... if you can call it that

The weekend was the first opportunity to get Sacré Bleu wet, but unfortunately the weekend was totally windless. But I was determined to at least get it wet. Just to remember what to do, and give the boat a lightest of shakedowns. Which raised the need to sort the elastic for the centre board.


You'll notice the new electric motor I've installed along with the mast mods.

Saturday 26 August 2017

Makeshift Lathe

A big thanks to Jeremy who made the new mast foot for me, he's an absolute star. All I can say his I owe him a lot of beers, as a new one form C-Tec was costed up at $250NZD!

I knew that I would have to do some extra work to the mast foot when I got hold of it. As I'd intentionally over estimated the spigot lengths to make sure I had enough length to enable me to make adjustments when I received the foot.

So how do I make the mods to the mast foot when I don't have a Lathe?

Use your power drill as a Lathe!

I clamped my drill in my vice, put the brass mast foot in the drill chuck, turned on to a high speed and used a file and hacksaw to make the mods. Surprisingly simple.

I needed to shorten the bottom spigot and round off the end. To help when the mast is placed in the foot socket. Plus - I didn't want to lose the mast foot again. So I need someway of stopping this. I stepped the top spigot down. Flattened one side and drilled through so I could attach a dyneima loop to the mast.

Bobs your Uncle - no more lost mast foot!

Tuesday 22 August 2017

I've been saved by JC

What can I say - JC has performed a miracle! That'll be Jeremy Carey just to be clear. Thanks to his fabulous skills with a lathe I may be able to get sailing soon!

Sunday 13 August 2017

Erection problems

So I'm being kept away form the water by jobs on the boat that need to be done while it's warm. Too warm it would seem, even for 10am on an otherwise wet month of August. I was worried that my West 205 epoxy, with a use by date of 01/01/2012 would not go off. I shouldn't have bothered looking for a local supplier of glue. As I can confirm that even if the hardener is dark brown the stuff goes off much quicker than you want it too!!! More of that in a bit...

So jobs to do. It's been awhile since I've sailed, and to be frank the uniqueness of rolling the boat over for the small performance gain I have decided is not worth it. This may have something to do with age? Needing to save as much energy as possible? ;-) or just that the foreshore in the UK is never really conducive to this procedure. Oh and the fact that the original downhaul line was about to break. Which meant it needed to be changed anyway.


Unfortunately this meant 'Drimmeling' out the spinnaker piston lock that the mast was originally built with, so I decided to put a mast head sheave box in instead. Tick.

After spending the requisite - almost £30 for a 10ps worth of injected plastic. Just because it is to do with sailing. I installed the mast head sheave. Meaning that I now have a conventional external main halyard system. No more rolling the boat over. Tick.

Next carbon over the holes that the old halyard system used. As a test for the super out of date epoxy. To my surprise the glue worked fine! Ace, my wallet is relieved. I think it's important to seal the mast. Especially the opening at the mast head. This should stop / slow the water coming in the mast when capsized. Giving me a little extra time to get not the board.

Doh! Whilst transporting the mast I seem to have lost the rotating mast foot. Balls! This is a problem, I'm hoping it fell off in the boat park. Otherwise it's air freight from NZ time, as they are not an off the shelf item.

I'm really do hope I can find this sucker, as I need to get my water wings before October and the Lyme Regis S.C Nationals. It's been quite a while since I last sailed (4?5? years!), and I know fitness is going to be an issue as I know I have a complete lack of it. My back isn't getting any better with age. Sitting at a desk all day, Scoliosis, tight hip flexors from a reasonable youth athletics career and falling out a tree all cause me quite a bit of pain. One of the reasons I went for the 3.7 in the first place. Hiking killed my back.

Back to the jobs.

Now to replace the 'intermediate shrouds'. Originally #384 had 3mm wire inters bonded to the mast. After a while sailing the boat the electrolysis created between the carbon and the stainless corroded the wire at the intersection. Causing the wire to break. At the time I decided to replace these with SK78, believing in the hype about it's, No / V Low stretch qualities. This resulted in a loss of power. As they did stretch.


Guy who I bought the boat back from had had some wire inters made up. So whilst sorting the mast it was a good time to put these on.

Now for the big test of the glue! I shouldn't have worried! I was intending to sink the hard eye into a bog mix of glue, by wrapping it down with peel ply. I wasn't working slow, but it seems 10am sun shine and a black mast was to much for my filler mix, and it went off before I got the carbon top layer over it and wrapped it down. Meaning I now have a large bump on the front of my mast.

Oh well I'm sure it will be secure enough. It just doesn't look very pretty. At some point I may cut it back and re-do it, but for now it will have to do.

Need to get on the water.

BTW - if you see a brass fitting that looks like this at B.S.C it's from my mast!!! Send me a message here!













Sunday 6 August 2017

Back in the game

After a time in the wilderness, I'm back in the game, having recently just bought back 'Sacré Blue' from Guy Revill who had been looking after her at Lyme Regis sailing club. More to follow...